ArangoDB v3.4 reached End of Life (EOL) and is no longer supported.

This documentation is outdated. Please see the most recent version here: Latest Docs

Troubleshooting datacenter to datacenter replication

Datacenter to datacenter replication is only available in the Enterprise Edition.

The datacenter to datacenter replication is a distributed system with a lot different components. As with any such system, it requires some, but not a lot, of operational support.

This section includes information on how to troubleshoot the datacenter to datacenter replication.

For a general introduction to the datacenter to datacenter replication, please refer to the Datacenter to datacenter replication chapter.

What means are available to monitor status

All of the components of ArangoSync provide means to monitor their status. Below you’ll find an overview per component.

  • Sync master & workers: The arangosync servers running as either master or worker, provide:
    • A status API, see arangosync get status. Make sure that all statuses report running.
      For even more detail the following commands are also available: arangosync get tasks, arangosync get masters & arangosync get workers.
    • A log on the standard output. Log levels can be configured using --log.level settings.
    • A metrics API GET /metrics. This API is compatible with Prometheus. Sample Grafana dashboards for inspecting these metrics are available.
  • ArangoDB cluster: The arangod servers that make up the ArangoDB cluster provide:
    • A log file. This is configurable with settings with a log. prefix. E.g. --log.output=file://myLogFile or --log.level=info.
    • A statistics API GET /_admin/statistics
  • Kafka cluster: The kafka brokers provide:
    • A log file, see settings with log. prefix in its server.properties configuration file.
  • Zookeeper: The zookeeper agents provide:
    • A log on standard output.

What to look for while monitoring status

The very first thing to do when monitoring the status of ArangoSync is to look into the status provided by arangosync get status ... -v. When not everything is in the running state (on both datacenters), this is an indication that something may be wrong. In case that happens, give it some time (incremental synchronization may take quite some time for large collections) and look at the status again. If the statuses do not change (or change, but not reach running) it is time to inspects the metrics & log files.
When the metrics or logs seem to indicate a problem in a sync master or worker, it is safe to restart it, as long as only 1 instance is restarted at a time. Give restarted instances some time to “catch up”.

What to do when problems remain

When a problem remains and restarting masters/workers does not solve the problem, contact support. Make sure to include provide support with the following information:

  • Output of arangosync get version ... on both datacenters.
  • Output of arangosync get status ... -v on both datacenters.
  • Output of arangosync get tasks ... -v on both datacenters.
  • Output of arangosync get masters ... -v on both datacenters.
  • Output of arangosync get workers ... -v on both datacenters.
  • Log files of all components
  • A complete description of the problem you observed and what you did to resolve it.

  • How to monitor status of ArangoSync
  • How to keep it alive
  • What to do in case of failures or bugs

What to do when a source datacenter is down

When you use ArangoSync for backup of your cluster from one datacenter to another and the source datacenter has a complete outage, you may consider switching your applications to the target (backup) datacenter.

This is what you must do in that case:

  1. Stop synchronization using:

    arangosync stop sync ...
    

    When the source datacenter is completely unresponsive this will not succeed. In that case use:

    arangosync abort sync ...
    

    See Stopping synchronization for how to cleanup the source datacenter when it becomes available again.

  2. Verify that synchronization has completely stopped using:
    arangosync get status ... -v
    
  3. Reconfigure your applications to use the target (backup) datacenter.

When the original source datacenter is restored, you may switch roles and make it the target datacenter. To do so, use arangosync configure sync ... as described in Reversing synchronization direction.

What to do in case of a planned network outage

All ArangoSync tasks send out heartbeat messages out to the other datacenter to indicate “it is still alive”. The other datacenter assumes the connection is “out of sync” when it does not receive any messages for a certain period of time.

If you’re planning some sort of maintenance where you know the connectivity will be lost for some time (e.g. 3 hours), you can prepare ArangoSync for that such that it will hold off re-synchronization for a given period of time.

To do so, on both datacenters, run:

arangosync set message timeout \
    --master.endpoint=<endpoints of sync masters in the datacenter> \
    --auth.user=<username used for authentication of this command> \
    --auth.password=<password of auth.user> \
    3h

The last argument is the period that ArangoSync should hold-off resynchronization for. This can be minutes (e.g. 15m) or hours (e.g. 3h).

If maintenance is taking longer than expected, you can use the same command the extend the hold-off period (e.g. to 4h).

After the maintenance, use the same command restore the hold-off period to its default of 1h.

What to do in case of a document that exceeds the message queue limits

If you insert/update a document in a collection and the size of that document is larger than the maximum message size of your message queue, the collection will no longer be able to synchronize. It will go into a failed state.

To recover from that, first remove the document from the ArangoDB cluster in the source datacenter. After that, for each failed shard, run:

arangosync reset failed shard \
    --master.endpoint=<endpoints of sync masters in the datacenter> \
    --auth.user=<username used for authentication of this command> \
    --auth.password=<password of auth.user> \
    --database=<name of the database> \
    --collection=<name of the collection> \
    --shard=<index of the shard (starting at 0)>

After this command, a new set of tasks will be started to synchronize the shard. It can take some time for the shard to reach running state.